How Thick Should a Custom Tin Box Be? A Buyer’s Guide by Application
Nov 19, 2026
A reasonable tinplate thickness to sample for many standard cookie tins first is 0.23 mm. If you are anticipating a wider lid to dent under the load you expect, you might want to try 0.25 mm or 0.28 mm on that lid. The problem is different with a small money tin. The lid might look fine, but the base has to withstand more than a kilogram of coins. The useful question is what part of the tin has to withstand what load.
This guide addresses decorative tinplate boxes and cans for gifts, savings and consumer products. Food examples are packaged in appropriate inner packaging such as a sealed pouch or individually wrapped pieces. Separate evaluation of the entire container and filling process is needed for direct filling, retorting or pressurising of cans.
Fast answer
Take the sheet thickness that has been used on a similar tin of similar size, closure and filling weight as close as possible.
For most standard cookie tins, start with 0.23 mm. If a particular part needs reinforcing, try 0.25 mm or 0.28 mm.
Request specifications for lid, body, and base separately. A thickness on a quotation may refer to just one component.
After any gauge change, check sliding lids, hinges and plugs removable. The assembled parts must be free moving and stay put.
Approve the sample for intended contents and protection for shipping. Evaluate the cost of an acceptable finished pack before you decide to go to a heavier stock.
Tinplate Thickness by Application: Where Do You Start?
The below figures are examples of sampling options, not minimum requirements or load ratings. If a supplier’s production sample is the same size and its closure and intended load are comparable to yours, that’s a good place to start. A picture of a similar-looking tin tells you a lot less.
Use and tin type
First sample point
What should determine the choice?
Pocket tins with guitar picks or wrapped mints
Use the gauge of the existing tool. A Jinyu hinged mint tin is 60 × 50 × 15 mm and uses 0.23 mm. Confirm the version of the slide lid separately.
Load the tin, open and shut it. A slide should glide without snagging or coming loose. A hinged lid should snap into its catch without squeezing the sides.
Sealed inner pouch tea or coffee tins
Ask for the next production tin of the same height, cross-section and lid. A quoted 0.23 mm sample is useful if those features agree.
Insert actual sealed pouch. If the lid closes on the empty tin, but catches the pouch, check usable height and the top fold before changing the metal.
Chocolate or seasonal gift tins with a wide biscuit
For a normal biscuit tin start with 0.23 mm. Compare 0.25 mm lid on larger lid if tooling allows. If the requirement is not met, consider 0.28 mm.
Check the largest unsupported area below the agreed handling or stacking load. Unload and check for a permanent dent. Check that the lid still fits evenly.
Charity collection cans and money boxes
0.23 mm JYZG-MT-09 Jinyu rectangular coin bank Depending on the size and structure, its range with removable lid is 0.23, 0.25 and 0.28 mm.
Test the intended coin mix and filled weight. Look at the base and how it is joined. On a model that has a plug, check that the plug is secure and that the tin is flush.
Worked with heavier presentation sets and gift tins.
Please provide a sample with attachments and gross weight, like handle, including contents. A bad standard is a similar size empty gift box.
Carry the filled pack as designed. Check for movement on the handle mounting, the surrounding panel, the latch and the base. See which part moves first.
deep drawn, windowed or heavily embossed tins
Begin with a gauge and steel grade that the supplier has successfully formed on the proposed tool. Request a sample prior to setting the gauge.
Look at drawn corners, metal frame around the window or embossing detail as applicable. Place the finished lid on the body.
Why Two Tins of the Same Size Might Need Different Gauges
A flat lid and a stepped lid
Two rectangular lids can have the same outside dimensions but different spans of unsupported metal. On one the flat surface runs almost to the rim; on the other a formed step interrupts that surface. Compare the effect of removing the same load. One decision is different, the flexible lid that goes back to shape versus one that holds a visible crease across the artwork.
A bag of tea and a can of coins
Or perhaps the tea buyer will most care about an unmarked display panel and enough room under the lid to hide the sealed pouch. The tin is heaviest at the time a collection organiser may touch it several times. Even if both buyers have selected the same outer shape, the tea buyer should approve the packed look; the organiser should also approve the base and withdrawal aperture under load.
A sliding lid and a lift off lid
The folded edges of the lid engage the body on a slide tin. Changing the gauge can change how those edges fit together. On a lift-off lid the buyer can see how evenly the cover sits around the rim, and how it comes off. In either case, try the lid on a body made up to the proposed production spec. A loose lid, held in the hand, can not tell you if the assembled box will work.
In all three comparisons, one material distinction matters. Gauge is the thickness of the nominal sheet thickness. Temper is related to formability and strength. Temper is a material condition. Tin coating mass is specified separately, normally in grammes per square metre per side. Tata Steel separately lists these properties in its packaging steel data. For tolerances and measurement points, see what to compare in a tinplate thickness quote.
When is it worth paying for thicker tinplate?
What the purchaser sees
First compare to request
How to read the output
One wide lid has a dent in it from stacking.
Compare two lid gauges on same body same load and carton arrangement. If the appearance of the stepped lid is acceptable, test it separately.
If only the heavier lid passes, price a lid only change. If both pass, apply agreed appearance and cost criteria.
Several tins arrive dented in the same spot.
Try a divider or carton arrangement that takes out contact at that point. Keep tin untouched.
Better packing may protect the tin without increasing its gauge, if the contact point is corrected and the damage is avoided.
When you lift, the metal around the handle bends.
Check mounting and support panel under the proposed gross weight. Compare a revised attachment to a heavier sheet.
Choose the modification that keeps the attachment in place and the lid in line when in use.
The sample is passed but the buyer wants something more solid.
Present two unlabeled samples of same finish and contents. Check out the prices and let the buyer take care of both.
If you like the heavier feel and it's worth the extra cost, consider it a design choice. It does not depend on load capacity.
For a cost check take one part with same blank area and steel density. Going from 0.23 to 0.25 mm increases that component’s theoretical steel mass by about 8.7%: (0.25 ÷ 0.23 − 1) × 100. That number does not tell you the increase in finished box price or load capacity. Please quote the difference in price per 1,000 acceptable finished tins, including any tooling adjustment or change in protective packing. This gives purchasing a number to work with.
Picking a gauge for a coin bank
This is an example of a sampling decision. The quantities establish a proposed test, not a tested capacity or factory load rating.
Buyer requires a reusable collection tin for 200 U.S. quarters. The U.S. Mint’s coin specifications list a nominal weight of 5.67 g for a circulating quarter, so the coins alone weigh around 1,134 g. First, see if 200 coins can actually be dropped through the slot in normal use. Then weigh the filled sample including tin and closure. The calculation tells you what you want to carry. The sample tells you if the tin can carry it.
Begin with the existing removable lid design. Ask supplier to identify the base, body and lid gauges on sample A. Fill, pass from counter to counter, place on a flat surface, empty through the opening intended for this purpose and replace the lid. Compare the base profile before and after. Check for rocking and if the lid pops up as it should.
The result tells us if we should order Sample B:
If A is flat, the base joint is good and the lid fits, leave A unless it fails some other agreed requirement. The heavier one needs to be justified beyond its availability.
If the base panel is bowed but the joint and closure are still good, ask if the tool can take the next base gauge. A 0.25 mm base is a useful comparison if A has a separate 0.23 mm base. Keep the body, lid, coin amount and handling procedure the same.
If it’s a plug-equipped version, check the withdrawal plug first if the joint loosens. The problem you see would remain untested with a thicker sidewall.
Take a picture of the loaded tin on the scale and a similar picture of the base before and after handling. The records are more informative about the purchasing decision than two blank samples labelled “standard” and “heavy duty.”
What to Approve prior to Bulk Production
Approval item
What record
Material and component parts
Sample revision and drawing. Nominal gauge and tolerance for lid, body and base. Steel grade or temper. Any difference between sample and quotation.
Packing condition
Contents, inner packaging, gross weight and orientation. See if the check is for a filled tin which is being used or an empty tin which is in transit.
Acceptance criteria
Load, handling sequence and number of opening cycles to be agreed before comparison of samples. Define unacceptable permanent dents, base rocking, closure release or binding.
Shipping protection
Use the intended carton, quantity per carton and dividers. Record if damage occurs on tin, insert, or contents.
Repeat orders
Maintain the approved sample and component specification. Agree on which changes to the material, tool, closure or packaging require additional approval.
FAQs
0.23 mm? Is that enough for a custom tin box?
It can be a good starting point for a standard cookie tin or a well-established small box design. Specify the portions that use 0.23 mm and test the filled specimen for conformance to the intended handling and appearance requirements.
Can the lid or base be thicker tinplate?
Yes, where the tooling can accommodate the change and the design allows for individual pieces. In a drawn tin, the body and bottom are supplied from the same blank and the base is not a separate sheet that can be upgraded independently.
A heavier gauge of tinplate will help prevent dents in transit.
It can help a panel to withstand a particular load. If a neighbouring tin is hitting the same corner in each carton, try changing the divider or the spacing as well. Make only one change at a time so you can tell what stopped the damage.
Can I turn a successful tin up in size with the same gauge?
Use it as a sample for comparison. A wider flat panel, a taller wall or a heavier fill changes what must be tested. Try the enlarged geometry in the original gauge before deciding if any part needs to be upgraded.
Ask for a thickness recommendation for your tin
Please send Jinyu your tin dimensions or model reference, packed product weight, lid design and shipping arrangement. If a sample is dented, sticks or comes loose, and it is an existing sample, include a photo of where it happens, and describe what the pack was doing at the time. This provides the supplier with enough information to suggest a starting gauge, identify the part worth changing and quote a meaningful comparison.
Read More